電機的拆卸和裝配流程專業知識

1、三相異步電機的拆裝維護1稻谷書屋（三）電機的拆解 motors dismantling2稻谷書屋1、準備工作 ready3稻谷書屋a、確認說明書 check manualb、工具的準備 prepare tools設備銘牌、型號、零件清單、標準件規格、組裝圖、維護注意事項nameplate, model, parts list, stand parts, assembly drawing, attention內六角扳手、棘輪扳手、呆扳手、延長桿、套筒、鐵/膠錘、撬棍等 hex wrench, ratchet wrench, solid wrench, extension rod, sleeve

2、wrench, hammer, crowbar, etc.注意：工具準備應以常用工具為主，取用方便的其他工具，用時取出即可！attention：ready common tools注意：從組裝圖可以分析出這臺設備正確的拆解順序.attention: know correct sequence by reading assembly drawing.4稻谷書屋c、輔助器材準備d、勞保用品的準備工作臺、吸油紙及垃圾桶、木方、塑料盒workbench, crane, oil-absorbing sheet, trashcan, wood, plastic box工作服/圍裙、防滑手套、薄手套、安全鞋

3、labour suit, slip-proof glove, mitten, safety shoe5稻谷書屋e、切斷能量源f、設備清潔關停管道閥門關停電力關停壓縮空氣等close pipeline valvepower offcompressed air off注意：正確執行l(wèi)oto程序！attetion：execute loto exactly去除設備表面污物，油污、灰塵等clean sewage, oil, dust on the equipment surface6稻谷書屋2、執行拆解 dismantling7稻谷書屋a、拆除前標記位置 marking before dismantli

4、ngb、電源線拆除 remove cable標記接線盒蓋 標記電機風扇罩 標記前端蓋 mark cable cap mark fan cap mark front end拆除接線盒蓋板并確認接線圖 remove cable check wiring8稻谷書屋c、拆解后端 dismantle back end電機風扇的拆除，應使用兩爪拉馬拉出。should using puller with two claws to remove plastic fan.拆除電機護罩 標記后端蓋位置 remove fan cap mark back end拆除散熱風扇 松后端螺栓 remove fan loos

5、e back screw 9稻谷書屋d、拆解前端 dismantle front end標記軸鍵 松前端螺栓 撬出前端蓋 mark shaft & key loose front screw pry front end 標記前軸承蓋板 松軸承蓋板螺栓 拉出前端蓋 mark loose bearing caps screw pull front end out應注意軸承空位內的調整墊片的數量和厚度。pay attention to the shim in bearing position.10稻谷書屋e、拆除后端蓋 remove back end 拆除后端蓋 清點零件 remove ba

6、ck end check parts 11稻谷書屋3、檢查 check12稻谷書屋檢查設備重要尺寸 check important dimensions 軸承孔位處的墊片厚度check thickness of the shim in bearing position檢查軸上密封部位尺寸及光潔度，有無磨損跡象check dimensions and smooth of sealing position, if corrode檢查密封件完好程度，有無損壞、磨花現象check seal is intact, if broken or scratch13稻谷書屋4、清潔整理 do 5s14稻谷書屋

7、a、所有拆解下來的螺栓、圓螺母、墊片、密封件等小件零件，都已安裝完畢都已安裝完畢。all dismangtled parts, have been installed. b、使用過的工具，都已擦拭干凈。all tools，have been cleaned.15稻谷書屋5、本章小節 summarize16稻谷書屋選用合適的拉馬 puller a.兩爪拉馬兩爪拉馬，用于保持力不大的場合，如塑料零件； two claw puller，is used to low thrust force. b.三爪拉馬三爪拉馬,用于普通場合的拆卸，如軸承、齒輪 three claw puller，is used

8、to remove bearing, gear. c.液壓液壓拉馬拉馬,用于需要省力或者空間受限的場合， hydraulic puller, is used to save effort or space constrained occasions .d.卡盤卡盤拉馬拉馬,用于邊緣圓滑，普通拉爪無法卡住的場合 chuck puller, is used to parts with round edge.17稻谷書屋（一）電機的裝配 motors reassemblying二、泵的裝配二、泵的裝配 pumps reassemblying18稻谷書屋1、準備工作 ready19稻谷書屋a、確認說明

9、書b、工具的準備設備銘牌、型號、零件清單、標準件規格、組裝圖、維護注意事項nameplate, model, parts list, stand parts, assembly drawing, attention內六角扳手、棘輪扳手、呆扳手、套筒、鐵/膠錘等hex wrench, ratchet wrench, solid wrench, sleeve wrench, hammer, etc.注意：一般的裝配順序是,從內到外，從下到上，先零件后部件，最后總裝。attention: assembly sequence is, from inside to outside, from botto

10、m to top, the first part components, final assembly.20稻谷書屋c、輔助器材準備d、勞保用品的準備工作臺、吸油紙及垃圾桶、木方、塑料盒workbench, crane, oil-absorbing sheet, trashcan, wood, plastic box, bowl工作服/圍裙、防滑手套、薄手套、安全鞋labour suit, slip-proof glove, mitten, safety shoe21稻谷書屋2、執行裝配 reassemblying22稻谷書屋安裝前端蓋于軸上 安裝前端蓋于外殼 安裝墊片于后端蓋 set up

11、front end & shaft set up front end & shell put shim安裝后端蓋 安裝后油封 安裝風扇 set up back end set up seal set up fan23稻谷書屋安裝前油封 安裝軸鍵 安裝風扇罩 set up front seal set up key set up fan cap接線盒安裝 套上軸護套并完成 wiring set up sheath & finish24稻谷書屋3、檢查 check25稻谷書屋檢查軸輸出端的徑向跳動 0.05mmcheck beating 0.05mm radial insp

12、ection of shaft output end檢查軸輸出端的端面跳動 0.03mm, 注意轉子的軸向游動量check end of output shaft runout 0.03mm, note the amount of axial removable rotor 檢查設備重要尺寸 check important dimensions 26稻谷書屋4、清潔整理 do 5s27稻谷書屋 a、所有拆解下來的螺栓、圓螺母、墊片、密封件等小件零件，必須按照一定的分類，使用合適的容器，妥善存放。keep nuts, screws, spacers, seals in box. b、拆解完的設備，應使用合適的工具清理廢油脂、密封膠、異物等污物。cleaning surface.28稻谷書屋5、本章小節 summarize29稻谷書屋a、電機的平衡檢查 mark 電機的轉子平衡對電機的使用至關重要，一般電動機出廠前都經過動靜平衡試驗，所以在我們?nèi)粘z修中，只需對電機軸用百分表進行跳動檢查，即可大概地確定電機的裝配平衡性。 the balance of the rotor is essential to the use of motor, general motors factory have been