腰輪流量計使用說明書中英文版

1、 1 概述 腰輪流量計是用于對管道中流量進行連續或間歇測量的高精度計量儀表。它具有精度高、可靠性好、重量輕、壽命長、安裝使用方便等特點，是容積式流量計的典型特點。 腰輪流量計主要由計量腔、密封聯軸器和計數器三部分組成?？涩F(xiàn)場指示累積流量和瞬時流量，配以發信器及流量智能控制儀，可實現遠距離測量和控制。廣泛用于石油、化工、電力、冶金、交通、食品加工、醫藥、國防、商業貿易等部門對石油及石油制品、化學溶液等流體的精確測量。 1.summarizelumbar wheel flow meter is used for pipeline liquid flow measurement of continu

2、ous or intermittent high-precision measurement instrumentation. it has high accuracy, good reliability, light weight, long life, easy installation etc. it is a typical positive displacement flow meter products.roots flow meter mainly by the measurement cavity, sealing the composition of the coupling

3、 and counters. the instructions can be cumulative and instantaneous flow of traffic, coupled with letters intelligent control device and flow meter, can realize remote measurement and control. it widely used in petroleum, chemical, electric power, metallurgy, transportation, food processing, medicin

4、e, defense, commerce and trade sectors such as oil and petroleum products, chemical solutions and other fluids accurate measurement. 2.工作原理當被測液體流經計量室時，在流量計的進出口形成 壓差，腰輪在此壓差的推動下旋轉。同時通過固定在腰輪軸上的一對驅動齒輪，使兩個腰輪保持連續旋轉。隨著腰輪的轉動，液體經由計量室被不斷排出流量計。每對流過的液體量是計量室容積的四倍，通過密封聯軸器、減速機構，將旋轉次數減速后傳遞到計數器，計數器即指示液體瞬時流量和累積流量。 在計

5、數器機構中安裝發信器即成了帶發信器的腰輪流量計。與顯示儀表或微機系統配套，可實現遠傳（定量、累積、瞬時等功能）自動化測量和控制。使用說明另見顯示儀表分類說明書。 2. workswhen the measured liquid flowing through the measuring chamber when the pressure in the formation of the import and export meter, waist-round under the impetus of pressure in the second rotation. at the same tim

6、e fixed on the waist by a pair of drive axle on the gear, there are two waist-round to maintain a continuous rotation. with the waist wheel rotation, the liquid is continuously discharged through the metering chamber flow meter. convection over the liquid for each volume is four times the volume of

7、metering chamber. through the sealing coupling, deceleration institutions, after slowing down the rotation number passed to the counter, counters that the instantaneous direction of liquid flow and cumulative flow.counting bodies in the installation of devices that have become with a letter writing

8、device roots flow meter. and display instruments or computer systems accessories, and can be realized remote (quantitative, cumulative, instantaneous and other functions) automatic measurement and control. see instructions display instrument classification manual. 3.主要零件材料組合材料零件alelll鑄鐵鑄鋁不銹鋼鑄鋼鑄鋁不銹鋼鑄

9、鐵鑄鐵鑄鋁不銹鋼殼體轉子蓋板轉子軸軸承 3. main parts and materials combinationsmaterialspartsalelllironaluminumstainlesscastaluminumstainlessironironaluminumstainlessshellrotorcoverrotor shaftbearing 4.性能和壓力損失曲線 4. performance and pressure drop curves 5.技術參數 公稱壓力（mpa）:0.6、1.0、1.6、2.5、4.0 工作溫度：（）：-1060 精度等級：0.5、0.2 流量范

10、圍：（m3/h）公稱通徑液體粘度3.0150mpa.s液體粘度3.0150mpa.s液體粘度3.0150mpa.s液體粘度3.0150mpa.s150.252.50.52.50.52.50.832.5200.252.52.50.52.50.832.5250.661.261.2626401.6163.2163.2165.316502.5255255258.325806601260126020608012100221002010033.310010010100201002010033.3100150402004020010020066.7200精度等級 0.5 0.2 5. specificati

11、onsworking pressure（mpa）：0.6，1.0，1.6，2.5，4.0temperature（）：-1060accuracy grade：0.5，0.2flow range（m3/h）diameter(mm)liquid viscosity 3.0150mpa.s liquid viscosity3.0150mpa.sliquid viscosity3.0150mpa.sliquid viscosity3.0150mpa.s150.252.50.52.50.52.50.832.5200.252.52.50.52.50.832.5250.661.261.2626401.6163

12、.2163.2165.316502.5255255258.325806601260126020608012100221002010033.310010010100201002010033.3100150402004020010020066.7200accuracy grade 0.5 0.2 6. 外形及安裝尺寸 6. overall and installation dimensions（1）鑄鐵型腰輪流量計外形尺寸(1) iron-based roots flow meter dimensionsmodel 型號lhibdd1n-dll-al15.0616023852100*100g11/

13、4ll-al20.0616023852100*1009065ll-al25.0618026068120*120g1/ll-al40.1240290881701501104-17.5ll-al50.1265305971901651254-c17.5ll-al80.12653401222462001608-17.5ll-al80.12654701642462001608-18ll-al100.15154251643052201808-18ll-al150.15605502254552852408-22（2）鑄鋼型腰輪流量計外形尺寸(2) cast steel wheel flow meter lu

14、mbar dimensionmodel 型號lhibdd1n-dll-el25.318026068120*120g11/4ll-al40.4300290881701501104-18ll-al50.43603151032761651254-18ll-al80.43603481282542001604-18ll-al100.35404351743302351904-22ll-al150.35605522274553002504-26（3）鑄鋁型腰輪流量計外形尺寸與鑄鐵型腰輪流量計外形尺寸相同(3) cast aluminum wheel flow meter lumbar dimension j

15、ust as (1) 7.腰輪流量計的安裝使用 7. lumbar wheel flow meter installation （1）流量計前應安裝過濾器，兩者表體上箭頭指向與流動方向一致(1).flow meter should be installed before the filter, the two arrows pointing in the body on the line with the flow direction（2）當被測液體含有氣體時，流量計前應安裝氣體分離器(2) recently tested liquid containing gas, flow meter s

16、hould be installed before the gas separator（3）不論管路是垂直還是水平安裝，但流量計的腰輪軸安裝成水平位置（即表度盤應與地面垂直）。(3)regardless of pipe is installed vertically or horizontally, but the flow meter installed in the waist into a horizontal position axle ( dial the table should be perpendicular to the ground)（4）流量計在正確安裝情況下，如果不易看

17、清讀數，可把計數器旋轉180度或90度均可。(4) flow meter installed in the right circumstances, if difficult to see clearly, can be rotated 180 degrees to the counter, or 90 degrees（5）節流閥應安裝在流量計進口處，開閉閥裝在出口處，使用開閉閥時要緩慢啟動，不要突然開閥。(5) throttle valve should be installed in the meter entrance, opening and closing valve install

18、ed in the exit of the use of open-close valve slowly to start, do not suddenly open valve(6) 嚴禁使用掃線蒸汽通過流量計prohibited the use of scan-line steam through the flowmeter（7）在連續使用部門，流量計需加旁通管道in the continuous use sector, need to add bypass pipe flow meter（8）流量計安裝前，管道需沖洗，沖洗時采用直管段（替代流量計位置）防止焊渣、雜物等進入流量計pre-i

19、nstallation flow meter, piping required to wash, rinse used straight pipe section (alternative flow meter position) to prevent the welding slag and debris from entering flow meter（9）嚴禁用水校驗鑄鐵、鑄鋼材質組成的流量計check water is strictly prohibited cast iron, cast steel material composition of flow meter （10）流量計

20、在使用時流量大小不得超過技術要求。流量計正常工作在最大流量7080%為優。when using the flow meter size should not exceed the technical requirements. flow meter to work at maximum flow rate 70 80% is good 。（11）被測液體如果具有化學腐蝕性，需選用不銹鋼材質的流量計，如果腐蝕性強，需選用0crl8ni12mo2ti材質的流量計。（12）流量計的安裝方法如右圖所示。flow meter installation method as shown on the rig

21、ht. 8 誤差計算及調整error calculation and adjustment（1） 流量計的基本誤差，由各檢定流量點的各次測得值分別按下式計算：（容積法）flow meters basic error, by the test flow point of the various measured values determined by the formulae=（vm-v）/v*100%e-流量計誤差（一般指累積誤差）取兩位有限數字e-meter error (generally refers to the cumulative error) to take a limited

22、 number of twovm-流量計測得值（即顯示值）vm-meter measured value (that is, with values displayed)v一經修正后，流量標準裝置測得值（實際值）v 1, as amended, the flow standard device measured value (actual value)由基本誤差計算公式知，當vmv時，流量計基本誤差為“+”值，表示流量計走快了。vmv時，流量計基本誤差為“-”值，表示流量計走慢了knowing from the basic formula for calculating the error,

23、when the vm v, the flowmeter basic error + value, indicating flowmeter gone too fast. vm v, the flowmeter basic error - value, indicating slow flow meter walk 為了使流量計誤差在基本誤差限之內，往往需要進行調整。即通過更換裝在計數器內的一對調節齒輪（調整牙）來改變機械傳動比，從而使得流量計的顯示值得到調整。in order to meter error in the basic limits of error, and he often

24、needs to be adjusted. that is mounted on the counter by replacing a pair of adjustment gears inside (adjusted teeth) to change the mechanical transmission ratio, allowing to adjust the meters display is worth.誤差調整不能改變流量計的流量特性，僅使其特性曲線人為地處于新的坐標系中。error can not change the meter to adjust the flow chara

25、cteristics, so only the curve artificially in a new coordinate system.一般來說，在規定的（或?qū)嶋H使用的）流量范圍內，其最大與最小流量檢定點的基本誤差范圍不大于規定的精度的基本誤差，均可通過誤差調整使其流量計基本誤差合格。in general, the provisions of (or actual use of) traffic within the maximum and minimum flow rate test points, the scope of the basic error of not greater

26、than the precision of the provisions of the basic error, the error can be adjusted to meter through the basic error of qualified .已使用過的流量計，一般先用原有的調節齒輪組進行誤差檢定，然后根據具體的誤差情況再進行調整。flow meter has been used, generally the first to use the original error of the regulation of gear group test, and then depend

27、ing on the error happen again to adjust.（2） 腰輪流量計誤差調整方法（誤差調整表使用說明）roots flowmeter error adjustment methods (error-adjusted using the instructions1. 設計時的標準雙層齒輪是35/38，在檢驗時若發現流量計走慢了，即出現（1）誤差，例如-1.02-0.32時，應將雙層齒輪35/38換成38/41，這時誤差曲線原點便由35/38齒輪對應的零位，上移到38/41齒輪相對應的+0.62的位置（參看調節齒輪表），這樣誤差曲線便處于新的坐標系統中，而流量計的誤差

28、被調整在-0.4+0.32的范圍內，便達到合格要求。design criteria for two-tier gears are 35/38, in the examination if the meter was found to go slow, that is, under (1) error, for example, -1.02 -0.32, should be replaced 38 double-deck gear 35/38 / 41, when the error curve corresponding to the origin will be zero by the 35

29、/38 gears spaces, moved to the 38/41 gear + 0.62 corresponding to the location (see gear table adjustment), so that the error curve will be at the new coordinate system, the flowmeter is adjusted error of -0.4 +0.32 in the context, we meet eligibility requirements.2. 流量計在使用過程中，由于工作條件的變化，誤差往往也會變化，導至超

30、差。只要誤差范圍不超過1%，一般均可以調整合格。例如儀表周期檢定后誤差為-0.12+0.66，就可以進行調整，首先觀看調節的雙層齒輪是多少的齒，例如調節的雙層齒輪是38/41齒輪，則應參考“調節齒輪標表”上的38/41處相對應的原坐標原點+0.62作為零位，下移至+0.43處對應的調節齒輪37/40調節雙層齒輪，即坐標原點下移-0.19，則誤差便調整到-0.40+0.47范圍內，保證合格。flow meter during use, due to changes in working conditions, the error will tend to change, leading to t

31、he ultra-poor. as long as no more than 1% error range, generally can be adjusted qualified. for example, periodic checking and testing instrument error -0.12 +0.66, it can be adjusted, first of all watch regulate how much the two-tier gear tooth, such as adjusting the double-deck gear is a 38/41 gea

32、r, you should refer to standard tables adjustable gear on the 38/41 at the origin corresponds to the original coordinates + 0.62 as zero, the next move to +0.43 at the regulation of gear 37/40 regulating the corresponding double-gear, that is down -0.19 coordinate origin, then the error will be adju

33、sted to -0.40 +0.47 range to ensure compliance.2. 校驗調整0.2級腰輪流量計具體方法按國家計量檢定規程jjg667-1997液體容積式流量計實施。check adjustment of 0.2 roots flowmeter specific methods by country metrological verification jjg667-1997 liquid volumetric flow meter, to implement。9. 配套 supporting儀表一般按以下配套出廠：40及其以上口徑配機械密封聯軸器。y1減速器和a5

34、計數器，帶發信器的流量計則配y2減速器；25及其以上口徑配磁性密封聯軸器、y1減速器和a5計數器，實現流量信號遠傳的流量計在本體上直接配gf類發信器。 用戶需要回零計數器a6，請?jiān)谟嗀洉r(shí)說明。instruments are generally governed by the following supporting factory: 40 and above, aperture coupling with mechanical seals. y1 reducer and a5 counters, flow meters with a letter device is equipped with

35、 y2 reducer; 25 caliber and above, with magnetic sealing couplings, y1 reducer and a5 counters, flow meters for traffic signals in the body of the fet class letters directly with gf devices. users need to return to zero counters a6, please note when ordering. 配套的計數器型號及性能指數 supporting counter model a

36、nd performance indexa5技術性能 a5 technical performance1、 指針指示 pointer instructions2、 滾輪累積 roller cumulative3 累積顯示6位 cumulative display 64. 表示單位l unit5.指針回轉方向和順時針 pointer to the direction and clockwise rotationa6技術性能 a6 technical performance1.指針指示 pointer instructions2.累積顯示6位 cumulative display 63 回零顯示6

37、位 back to zero shows 64. 表示單位l unit5.指針回轉方向和順時針 pointer to the direction and clockwise rotation注：a5計數器；滾輪及指示累積顯示。a6計數器；上排滾輪累積顯示，指針及下排滾輪具有回零功能note: a5 counter; wheel and instructions cumulative display. a6 counter; on the row roller accumulation showed that the pointer and the next row of rollers wit

38、h a return to zero function。 配套的計數器型號性能及技術參數 supporting counter model performance and technical parametersqf-1特點features1. 采用二線制（信號與供電共用導線） using two-wire (signal and power sharing cable)2.無觸點，發信可靠 no contact, letters and reliable3.傳輸距離遠，方波輸出 transmission distance and square-wave output4.本質安全型防爆和隔爆型

39、防爆intrinsically safe explosion-proof and explosion-proof 技術參數 specifications1. 輸出信號：矩型電壓脈沖高電平大于8.5v，低電平小于4.5voutput signal: rectangular high voltage pulse is greater than 8.5v, low is less than 4.5v2. 發信頻率與配套流量計流量大小成正比letter frequency and matching the size proportional to the flow meter3. 允許工作電壓：dc1

40、2v-dc15v. 配接安全柵時為dc12vallowable working voltage: dc12v-dc15v. with access barrier when dc12v4. 遠傳距離：1km（金屬導線電阻39歐）remote distance: 1km (metal wire resistance 39 5. 環境溫度：-10+65ambient temperature: -10 +65 6. 防爆等級：exiact5,dbt4 explosion-proof grade: exia ct5, d bt4 qf- 特點features1. 采用三線制（正電源線，信號線與電源地線

41、） using three-wire ( power cord, signal lines and power supply ground)2.無觸點，發信可靠 no contact, letters and reliable3.傳輸距離遠，方波輸出 transmission distance and square-wave output4.本質安全型防爆和隔爆型防爆intrinsically safe explosion-proof and explosion-proof 技術參數 specifications1.輸出信號：矩型電壓脈沖高電平大于9v，低電平小于1voutput signal

42、: rectangular high voltage pulse is greater than 9v, low is less than 1v2. 發信頻率與配套流量計流量大小成正比letter frequency and matching the size proportional to the flow meter3. 允許工作電壓：dc11v-dc15v. 配接安全柵時為dc12vallowable working voltage: dc11v-dc15v. with access barrier when dc12v4. 遠傳距離：1km（金屬導線電阻39.2歐）remote dis

43、tance: 1km (metal wire resistance 39.25. 環境溫度：-10+65ambient temperature: -10 +65 6. 防爆等級：exiact5,dbt4 explosion-proof grade: exia ct5, d bt4 qf-a 特點features1. 采用三線制（正電源線，信號線與電源地線）using three-wire ( power cord, signal lines and power supply ground)2. 無觸點，發信可靠 no contact, letters is reliable3. 傳輸距離遠，方

44、波輸出 transmission distance and square-wave output4. 本質安全性防爆隔爆型防爆 intrinsically safe explosion-proof and explosion-proof 技術參數 specifications1. 允許工作電壓 ：dc12vallowable working voltage:dc12v2. 輸出信號：矩形電壓脈沖dc12v供電時，高電平大于8.5v，低電平小于4.5voutput signal: rectangular high voltage pulse is greater than 8.5v, low i

45、s less than 4.5v3. 發信頻率與配套流量計流量大小成正比letter frequency and matching the size proportional to the flow meter4. 防爆等級：exiact5,dbt4 explosion-proof grade: exia ct5, d bt45. 遠傳距離：1km（金屬導線電阻39.2歐）remote distance: 1km (metal wire resistance 39.26. 使用環境溫度：-10 +65 ambient temperature: -10 +65 7. 輸出接管尺寸：普通及本安型，

46、內螺紋m10*1；隔螺紋m20*1.5output over size: ordinary and intrinsically safe type, internal thread m10 * 1; every other thread m20 * 1.58. 穿線內孔尺寸：普通級本安型5.6（直徑），隔爆型4.5（直徑）threading inside the hole size: normal level intrinsically safe 5.6 (diameter), flameproof 4.5 (diameter)qf- 特點features1. 采用三線制（正電源線，信號線與電

47、源地線）output over size( power cord, signal lines and power supply ground)2. 無觸點，發信可靠 no contact, letters is reliable3. 傳輸距離遠，方波輸出 transmission distance and square-wave output4. 本質安全性防爆隔爆型防爆 intrinsically safe explosion-proof and explosion-proof 技術參數 specifications1. 輸出信號：矩形電壓脈沖，dv24v供電時，高電平大于9v，低電平小于0

48、.5voutput signal: rectangular high voltage pulse is greater than 8.5v, low is less than 4.5v2. 發信頻率與配套流量計流量大小成正比letter frequency and matching the size proportional to the flow meter3. 允許工作電壓：dc24vallowable working voltage:dc24v4. 遠傳距離：1kmremote distance: 1km5. 使用環境溫度：-10 +65 ambient temperature: -10

49、 +65 6. 輸出接管尺寸：m10*1output over size：m10*1gf-特點：features1. 采用三線制 output over size2. 無觸點，發信可靠 no contact, letters is reliable 3. 發信精度高，特別適用于需要進行小量定量控制的場合letters of high precision, especially in applications that require a small amount of quantitative control of occasions技術參數 specifications1. 輸出信號：矩形電

50、壓脈沖，dv24v供電時，高電平大于9v，低電平小于0.5voutput signal: rectangular high voltage pulse is greater than 9v, low is less than 0.5v2. 發信頻率與配套流量計流量大小成正比letter frequency and matching the size proportional to the flow meter3. 允許工作電壓：dc12vallowable working voltage:dc12v4. 遠傳距離：1kmremote distance: 1km5. 環境溫度：-40+60 相對

51、濕度：10%85% ambient temperature: -40 +60 relative humidity: 10% 85%gf-特點：features1. 采用三線制 output over size2. 無觸點，發信可靠 no contact, letters is reliable 3. 發信精度高，特別適用于需要進行小量定量控制的場合letters of high precision, especially in applications that require a small amount of quantitative control of occasions技術參數 sp

52、ecifications1. 輸出信號：矩形電壓脈沖，高電平大于20v，低電平小于1voutput signal: rectangular high voltage pulse is greater than 20v, low is less than 01v2. 發信頻率與配套流量計流量大小成正比letter frequency and matching the size proportional to the flow meter3. 允許工作電壓：dc12vallowable working voltage:dc12v4. 遠傳距離：1kmremote distance: 1km5. 環

53、境溫度：-40+60 相對濕度：10%85% ambient temperature: -40 +60 relative humidity: 10% 85% 發信參數公稱通徑gf-、gf-發信器qf發信器l/pp/sl/pp/s1520250.0044251883.24400.04111.10.144.44500.04173.60.169.44800.1166.650.533.33800.1277.8127.781000.1277.8127.781500.4173.6169.44mf系列420ma模擬量輸出信號特點1. 四線制（正電源線、420ma電流線、脈沖信號線、電源地線）注：僅要420ma輸出時為三線制，供貨時脈沖信號線未外引。（需要時，訂貨合同注明）2. 流量計直接輸出420