環氧樹脂水下底漆的施工方案

1、環氧樹脂水下底漆的施工方案intended uses用途環氧樹脂水下底漆設計用于新結構平臺的維護保養以及暴露于海上的嚴重銹蝕部分如平臺支架，水面以上管道和水下管道，采用潛水員水下施工方法。this product is designed for maintenance of new construction platform, together with all serious corrosion parts exposed to marine environment including platform support, pipeline above water and underwater

2、 application can be done by diverproductdescription產品簡介二罐裝，無溶劑環氧樹脂涂料，用于長期保護浸于水中或潮汐的設備和平臺。two packages, solvent-free, epoxy resin paint, suitable for long term protection of equipmentsand plat forms immersed in water or tidelandproductinformation產品數據volume solids 體積固體份50%ccording 10 100%dry film thic

3、kness 干膜厚度3 mm-6 mm 3毫米-6毫米theoretical coverage 理論涂布率0.1m2 /kg at 100% volume solids and 6000 microns of dry film thickness 0.1平方米/公斤,以規定的體積固體份和6000微米干膜厚計practical coverage 實際涂布率allow appropriate loss 允許適量損耗color 顏色green after stirring(a: yellow , b: blue)攪拌后呈綠色（甲：黃色， 乙：藍色）application details施工詳述mix

4、 radio 混合比2 parts to 1 part by weight 重量比 2：1method of application 施工方法only daub by hand 只可用于手工涂抹thinner 稀釋劑 not necessary 不需要cleaner 油漆設備清洗劑 c003pot life 使用期 20-1h 小時（use within 30minutes） 20-1h 小時（應于30分鐘內使用）storage 貯存期 one year 一年drying time 干燥時間substratetemperature底材溫度,touch dry表干（h）hard dry硬干(h）

5、over coating interval覆涂間隔mix最短max最長52535/1684/storage andhandling貯存與管理storage 貯存 store under dry, cool conditions 貯存于干涼條件下pack size 包裝規格 a;20kg in 20 liter container 甲:20公斤裝于20公升容器中 b:10kg in 10 liter container 乙:10公斤裝于10公升容器中flash point 閃點 no flash point in normal 正常情況下沒有閃點specific gravity 比重 1.6kg

6、/l 1.6公斤/公升specification and surface preparation技術要求及表面處理iron or steel:remove grease to sspc-sp1 by solvent cleaning. remove weld slag, smooth welded seams and sharp edges. blast clean to white metal according to sspc-sp10 or swedish standard sa2.5. the steel roughness should be no more than 75um af

7、ter blasting. in particular area the the surface should be st3 standard with power tool.鐵與鋼：用溶劑清洗除去油脂，去除焊渣，并磨平焊道及尖銳邊緣，噴砂處理至白鐵狀為 sspc-sp10或 sa2.5瑞典標準sis055900,噴砂后表面粗糙度不大于75微米，在特殊區域，表面應用動力工具處理至st3標準。limitations 限制 in calm and tide less condition and good weather, this product may be manually applied t

8、o small surface under water by driver, for tube construction, firstly twine pvc net around the new blasted construction tightly, then daub by hand.在天氣良好，風平浪靜，無潮水狀況下，本產品可由潛水員在水下就小面積部分進行手工涂裝，對于管式鋼結構來說，應先將pvc鋼緊緊纏繞在新噴砂的結構上，然后用手工涂抹。safety precautions 安全措施this product should be used in painting area by pr

9、ofessional operators. when painting, please refer to product data sheet and msds. consult our company if consumers could not completely understand the precautions for safety and health when applying this product.although this paint is flammable, so must be far away from open flames. if paint gets in

10、 touch with skin, was fully with large amount of fresh water and soap or appropriate commercial cleaner. in case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately. recommend face guard with ventilation pipe for the sake of no absorption of p

11、aint fog and harmful solvent gas, especially in bad ventilation.handle empty containers with care and do not bring about environmental contamination.notice: if consumers have not taken effective safety precautions (refer to the specifications), our company will not be responsible for any accident. 本產品由專業人緣在工業場所使用，使用時請參照本說明書及健康安全手冊,如客戶在使用本產品前,未能仔細了解有關產品的健康安全知識，請與本公司聯系。該涂料為無溶劑型涂料，為避免事故或危險發生，應采取最低限度的安全措施如下：此涂料為可燃涂料，應遠離火星和明火。采取有效措施以防止皮膚和眼睛與涂料接觸(如使用工作服，手套，護目鏡，面罩及涂防護油等)