系統出錯信息解釋及解決方案.docx

系統出錯信息解釋及解決方案一、BIOS中的提示信息提示信息 說明 Drive A error 驅動器A錯誤 System halt 系統掛起 Keyboard controller error 鍵盤控制器錯誤 Keyboard error or no keyboard present 鍵盤錯誤或者鍵盤不存在 BIOS ROM checksum error BIOSROM 校驗錯誤 Single hardisk cable fail 當硬盤使用Cable選項時硬盤安裝位置不正確 FDD Controller Failure BIOS 軟盤控制器錯誤 HDD Controller Failure BIOS 硬盤控制器錯誤 Driver Error 驅動器錯誤 Cache Memory Bad, Do not Enable Cache 高速緩存Cache損壞，不能使用 Error: Unable to control A20 line 錯誤提示：不能使用A20地址控制線 Memory write/Read failure 內存讀寫失敗 Memory allocation error 內存定位錯誤 CMOS Battery state Low CMOS沒電了 Keyboard interface error 鍵盤接口錯誤 Hard disk drive failure 加載硬盤失敗 Hard disk not present 硬盤不存在 Floppy disk(s) fail (40) 軟盤驅動器加載失敗，一般是數據線插反，電源線沒有插接，CMOS內部軟驅設置錯誤 CMOS checksum error-efaults loaded. CMOS校驗錯誤，裝入缺省(默認)設置 二、BIOS刷新失敗后，Bootblock啟動時出現的提示信息提示信息 說明 Detecting floppy drive A media. 檢測軟驅A的格式 Drive media is : 1.44Mb1.2Mb 720Kb 360K 驅動器格式是1.44Mb、12Mb、720kb、360kb的一種 DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER 磁盤引導失敗，插入系統盤后按任意鍵繼續 三、MBR主引導區提示信息提示信息 說明 Invalid partition table 無效的分區表 Error loading operating sy stem 不能裝入引導系統 Missing operating system 系統引導文件丟失 說明：如果在計算機啟動過程中，在硬件配置清單下方(也就時在平時正常啟動時出現Starting Windows 98的地方)出現不可識別字符，此時可判斷硬盤分區表損壞。如果你的硬盤上有重要資料，這時你不要輕易進行分區，可找專業的數據恢復公司。四、DOS活動分區中的提示信息提示信息 說明 Invalid system disk 無效的系統盤 Disk I/O error, Replace the disk and press any key. 磁盤I/O錯誤，替換磁盤后按任意鍵(當C盤系統文件丟失或被破壞時出現該提示信息。這時可能SYS C:為修復系統文件) Invalid Media Type reaching Drive C： 無效的盤媒體格式說明，也就是C盤沒有格式化或者是其他操作系統的磁盤格式如NTFS Invalid Boot Diskette Boot Failure 無效的啟動盤，啟動失敗 五、IO.SYS中的提示信息提示信息 說明 Insert diskette for drive and press any key when ready 插入磁盤到驅動器中后按任意鍵 Your program caused a divide overflow errorIf the problem persists, contact your program vendor 你的程序?qū)е乱绯鲥e(cuò)誤。如果該問題還存在，請聯系你的程序供應商 Windows has disabled direct disk access to protect your long filenames Windows 不能直接訪問受保護的長文件名 The system has been halted. Press Ctrl+Alt+Del to restart your computer 系統掛起，按Ctrl+Alt+Del重新啟動你的計算機 You started your computer with a version of MS-DOS incompatible with this version of Windows. Insert a Startup diskette matching this version of Windows and then restart 你啟動的MS-DOS版本與Windows版本不兼容，請插入與Windows版本匹配的系統盤后再重啟 This version of Windows requires a 386 or better processor 該Windows版本需要386以后的CPU支持 A20 hardware error. Contact technical support to identify the problem 地址線A20錯誤。聯系技術支持來識別該問題 Starting Windows 98. 正在啟動Windows 98 Windows 98 is now starting your MS-DOS-based program Windows 98正在啟動基于MS-DOS的程序 Windows 98 is now restarting. Windows 98正在重新啟動 Press Esc now to cancel MS-DOS mode and restart Windows 98. 按Esc退出MS-DOS 模式，重新啟動Windows 98 There is an unrecognized command in your CONFIG.SYS file 在你的CONFIG.SYS文件中有不可識別的命令 The following command in your CONFIG.SYS file is incorrect: 在你的CONFIG.SYS有下列錯誤命令 The sector size specified in this file is too large: 該文件中指定的扇區太大 The following file is missing or corrupted: WIN.COM COMMAND.COM 下列文件丟失或被破壞：WIN.COM和COMMAND.COM There is an invalid country code or code page in your CONFIG.SYS file 在你的CONFIG.SYS里有一個無效的國家代碼 There is an error in the COUNTRY command in your CONFIG.SYS file 在你的CONFIG.SYS里有一個錯誤的設置國家命令 There is not enough memory for the COUNTRY.SYS file 沒有足夠的內存來加載COUNTRY.SYS文件 Remove some drivers from your CONFIG.SYS file, and then try again 請從CONFIG.SYS文件中刪除部分驅動程序，然后再試 Remove some drivers, and then try again 去除一些驅動程序，然后再試。這里的驅動程序是指在CONFIG.SYS中使用device或devicehigh命令加載的程序文件 Remove some disk drivers from your CONFIG.SYS file, and then try again 從你的(CONFIG.SYS)移去部分程序，然后再試 The configuration specified in your CONFIG.SYS file is too large for memory 調整你的CONFIG.SYS文件以獲得足夠大的內存 You have too many block devices specified in your CONFIG.SYS file 調整你的CONFIG.SYS文件以獲得block devices The STACKS setting(s) in your CONFIG.SYS file are incorrect 在你的CONFIG.SYS中堆棧設置不正確 Default stack settings will be used instead 缺省的堆棧設置將被替代使用 There is an error in your CONFIG.SYS file on line XX 在你的CONFIG.SYS里XX行錯誤 Warning: Logical drives past Z exist and will be ignored 警告：邏輯驅動器Z已經存在，將被忽略 Type the name of the Command Interpreter (e.g., C:WINDOWSCOMMAND.COM) Press any key to continue 請輸入命令解釋器的文件名(如：C:WIN DOWSCOMMAND.COM)后，按任意鍵繼續 Windows is bypassing your startup files Minimal network support will be loaded if available Windows 正在跳過你的啟動文件。如果網絡可用，最小網絡支持將被加載 Windows is starting the command prompt only Windows正在啟動命令字符模式 Windows will prompt you to confirm each startup command Windows將提示你確認每一個啟動命令 The compression driver cannot be set up correctly 壓縮驅動程序不能被正確加載 Get a version from your vendor that is compatible with this version of Windows 從你的供應商那里獲得一個與Windows版本相兼容的版本 Process the system registry 運行系統注冊表 Create a startup log file (BOOTLOG.TXT) 創建啟動日志BOOTLOG.TXT文件 Process your startup device drivers (CONFIG.SYS) 運行CONFIG.SYS文件中的設備驅動 Process your startup command file (AUTOEXEC.BAT) 運行AUTOEXEC.BAT中的啟動命令 Load the Windows graphical user interface 裝入WINDOWS圖形用戶界面(GDI) Warning: Windows has detected a registry/configuration error. Choose, Command prompt only, and run SCANREG 警告：Windows檢測到一個注冊表或配置錯誤選擇DOS操作模式，運行SCANREG Warning: Windows has detected a compressed drive access error. Choose Safe mode command prompt only, to help you identify the problem 警告：Windows檢測到一個訪問壓縮驅動器錯誤，選擇安全模式下的MS-DOS，來幫助你識別這個問題 Warning: Windows did not finish loading on the previous attempt. Choose Safe mode, to start Windows with a minimal set of drivers 警告：Windows在剛才嘗試后不能夠完成加載，選擇安全模式，用最小驅動啟動你的電腦 Warning: Windows multi-boot may not function correctly Check for system files in your root directory with conflicting extensions 警告：Windows不能夠正確完成多系統啟動，在你的ROOT目錄里檢查不一致的系統文件 Warning: the system configuration manager failed to run. Some of your real-mode device drivers may not initialize properly 警告：系統管理器運行失敗，一些實模式驅動可能沒有正確初始化 The BUFFERS setting(s) in your CONFIG.SYS file are too large. Default buffer settings will be used instead 在你的CONFIG.SYS里BUFFER設置太大。默認的BUFFER緩沖器設置將被使用 A memory allocation error occurred during startupBR Restart your computer and select Interactive Start to identify the problem 在啟動過程中內存分配發生錯誤，請重新啟動你的計算機然后選用交互式方式啟動來確定故障原因 Warning: the high memory area (HMA) is not available Additional low memory (below 640K) will be used instead 警告：高端內存不可用，低端內存將被代替使用 There is not enough memory for Windows. Remove some drivers from your CONFIG.SYS file, and then try again 對Windows來說沒有足夠的內存，請從CONFIG.SYS文件中移去部分加載的程序，然后再試著啟動你的讀入計算機 Your previous MS-DOS files were not found. 舊的MS-DOS文件沒有找到，這常見于使用雙啟動的系統，另一個系統是DOS6 Your previous MS-DOS version is not supported. MS-DOS startup failed 舊的MS-DOS版本不支持。MS-DOS啟動失敗 Now loading your previous version of MS-DOS, please wait 現在正在加載舊的MS-DOS版本，請等待 Invalid setting in the MSDOS.SYS file:An internal stack overflow has caused this session to be halted MSDOS.SYS 文件中無效的設置選項，系統堆棧溢出，系統掛起 Change the STACKS setting in your CONFIG.SYS file, and then try again 請改變CONFIG.SYS文件中的STACK設置，然后再試 Stack overflow 堆棧溢出 Integer divide by 0 整數被0除 Not enough space for environment 沒有足夠的空間 Run-time error 運行錯誤 Floating-point support not loaded 浮點運算支持沒有裝入 Null pointer assignment 無效的斷點分配六、COMMAND中的提示信息提示信息 說明 Stack overflow 堆棧溢出 Integer divide by 0 分母是0 Not enough space for environment 磁盤沒有足夠的空間 Run-time error 時鐘錯誤 No fixed disks present 沒有硬盤存在 Insufficient memory 內存不足 Invalid drive specification 無效的驅動器名 Invalid characters in volume label 無效的盤符 Invalid Volume ID 無效的卷標ID號 No target drive specified 目標驅動器沒有定義 missing operating system 系統文件丟失 Non system Disk or Disk Error 不是系統盤或磁盤錯誤 Replace Disk and Press Anykey To Reboot 替換磁盤，按任意鍵重新啟動 七、SYS傳送系統文件時的提示信息提示信息 說明 Cannot find System Files 不能找到系統文件 System transferred 系統傳送完畢 Disk unsuitable for system disk 目標磁盤不適合做系統盤 八、FORMAT中的提示信息提示信息 說明 Unable to write BOOT. 不能寫引導扇區 Invalid media type 無效的磁盤類型 Parameters not supported 參數不支持 Cannot format a network drive 不能格式化網絡驅動器 Invalid media or Track 0 bad - disk unusable 無效的磁盤或磁道損壞，磁盤不可用 Format terminated 格式化終止 Disk Boot failure 磁盤BOOT區錯誤 Invalid system disk 無效的系統磁盤 Disk I/O error，Replace the disk, and then press any key 磁盤I/O錯誤，請換盤后按任意鍵。通常在讀寫軟盤時出現此類錯誤 Non-System disk or disk error，Replace and strike any key when ready 無系統的磁盤或磁盤錯誤，請?zhí)鎿Q后按任意鍵 Too many open files 打開的文件太多 Access denied Insufficient memory 沒有足夠的內存訪問被拒絕 Invalid drive specification 無效的盤符說明 Parse Error XX 分析錯誤 XX Incorrect MS-DOS version 不正確的MS-DOS版本 X percent completed 格式化正在進行，已經完成X% Format complete. 格式化完成 XX bytes in bad sectors XX字節的壞扇區 XX bytes total disk space 磁盤的全睰占湮猉X字節 XX bytes available on disk 磁盤的可使用空間為XX字 Volume label (11 characters, ENTER for none)? 請輸入磁盤卷標(總共11個字符，按回車為空) Format not supported on drive X Format 命令不支持驅動器X Invalid device parameters from device driver 無效的設備驅動參數 Error writing FAT 寫FAT表錯誤 Error writing directory 寫DIR目錄表錯誤 Cannot format an ASSIGN or SUBST drive 不能格式化ASSIGN和SUBST指定的驅動器 Cannot find System Files 沒有找到系統文件 Cannot format a network drive 不能格式化網絡驅動器 Invalid characters in volume labe l 磁盤卷標中存在非法字符 Parameters not supported 參數不支持 Format terminated 格式化意外終止 Disk unsuitable for system disk 這個磁盤不適合作為系統盤 Unable to write BOOT 不能寫B(tài)OOT區 Error reading directory 讀DIR目錄區錯誤 No target drive specified 目的驅動器沒有說明 and press ENTER when ready 準備好后按回車鍵 System transferred 系統傳送完畢 Enter current volume label for drive X 請為驅動器X輸入磁盤的卷標 Parameters not compatible with fixed disk 參數與硬盤不兼容 Volume Serial Number is XXXX 分區格式化時隨機產生的序列號是：XXXX Format broken 格式化被強行終止 Format not available on drive XX 不能在驅動器XX上使用格式化命令 on-System disk or disk error 沒有系統盤或磁盤錯誤 Bad Partition Table 錯誤的硬盤分區表 Parameters not supported by drive 該驅動器不支持這些參數 Insert DOS disk in drive A 請?jiān)隍?qū)動器A中插入DOS系統盤 WARNING, ALL DATA ON NON-REMOVABLE DISK DRIVE %1: WILL BE LOST! Proceed with 警告：硬盤分區X中的所有數據都將丟失，確定執行格式化命令嗎? Format another (Y/N)?! 還格式化其他盤嗎 Error reading partition table 讀硬盤分區表錯誤 Error writing partition table 寫硬盤分區表錯誤 Parameters not compatible 參數不匹配 XX allocation units available on disk 磁盤上有XX可用簇 XX bytes in each allocation unit 每個簇有大小為XX字節 Same parameter entered twice 相同的參數被輸入兩次 Must enter both /T and /N parameters /T和/N參數必須同時使用 There is not enough room to create a restore file 沒有足夠的空間來建立恢復文件 You will not be able to use the UNFORMAT utility 你將不能使用UNFORMAT工具來恢復你的硬盤數據 There is not enough disk space for system files 沒有足夠的空間來存儲系統文件 This disk cannot be unformatted 這個磁盤不能被反格式化 There was an error creating the format recovery file 在建立恢復文件時產生了一個錯誤 Volume label is not supported with /8 parameter 該驅動器不支持/8參數 Insufficient memory to load system files 沒有足夠的內存裝入系統文件 Insufficient memory. 內存不足 Calculating free space (this may take several minutes). 正在統計磁盤空間(可能要花上幾分鐘時間) 九、FDISK中的提示信息提示信息 說明 Delete Primary DOS Partition 刪除主DOS分區 Delete Extended DOS Partition 刪除擴展DOS分區 Delete Logical DOS Drive(s) in the Extended DOS Partition 刪除邏輯DOS分區 WARNING! Data in the deleted Primary DOS Partition will be lost 警告：主DOS分區的數據將全部丟失 WARNING! Data in the deleted Extended DOS Partition will be lost. Do you wish to continue (Y/N)? 警告：擴展分區中的數據將全部丟失，你真的繼續嗎 Delete Logical DOS Drive(s) in the Extended DOS Partition 刪除擴展分區下的邏輯分區 WARNING! Data in a deleted Logical DOS Drive will be lost What drive do you want to delete? Are you sure (Y/N)? 警告：邏輯分區中的所有數據都將丟失，你刪除哪個驅動器？你真的確定嗎 Display Partition Information 顯示分區內容信息 The Extended DOS Partition contains Logical DOS Drives. 擴展DOS分區中包含DOS邏輯分區 Do you want to display the logical drive information (Y/N)? 你想顯示邏輯分區的信息嗎 Display Logical DOS Drive Information 顯示邏輯分區信息 Enter partition size in Mbytes or percent of disk space (%) to create a Primary DOS Partition. 輸入所建立主DOS分區的容量，單位是百分比 Enter logical drive size in Mbytes or percent of disk space (%). 請輸入邏輯分區容量大小或磁盤空間的百分比 Enter Volume Label? 請輸入卷標 Enter partition size in Mbytes or percent of disk space (%)to create an Extended DOS Partition. 請輸入擴展DOS分區的容量大小或磁盤空間的百分比 Do you wish to use the maximum available size for a Primary DOS Partition 你想使用全部磁盤空間作為主DOS分區嗎 Change Current Fixed Disk Drive . Enter Fixed Disk Drive Number (X) 當你掛接兩個以上硬盤時，在FDISK的系統菜單中將多一個第5項，選擇第5項時，將提示：請輸入硬盤的序號 Fixed Disk Drive Status 硬盤狀態 Data in the deleted Primary DOS Partition will be lost.What primary partition do you want to delete?Do you wish to continue (Y/N)? DOS主分區中的數據將全部丟失。你準備刪除哪個主分區？你想繼續嗎 Data in the deleted Non-DOS Partition will be lost.What Non-DOS partition do you want to delete?Do you wish to continue (Y/N)? 非DOS分區的數據將全部丟失。你準備刪除哪一個非DOS分區？你要繼續嗎 You MUST restart your system for your changes to take effect 你必須重新啟動你的計算機你所做的所有改變才有效 Any drives you have created or changed must be formatted 你新建的分區或改變的分區必須被格式化后才可用 Shut down Windows before restarting 在重啟之前請關閉Windows Your computer has a disk larger than 512 MB. This version of Windows includes improved support for large disks, resulting in more efficient use of disk space on large drives, and allowing disks over 2 GB to beformatted as a single drive 你的計算機掛接了一個大于512M的硬盤。該版本的Windows支持大硬盤，能夠更有效的使用大硬盤上的磁盤空間，并充許單個分區大于2GB Press Esc to exit FDISK 按Esc退出FDISK This drive is FAT16 by default, switch to FAT32 (Y/N)? 這個驅動器默認是FAT16模式，真的轉換為FAT32模式嗎 This drive must be FAT32 because its size is 2048 MB 當分區的空間大于2048MB時，這個分區必須使用FAT32磁盤數據格式 This drive must be FAT16 because its size is too small to be FAT32 因?yàn)檫@個分區對于FAT32格式來說太小，所以這個分區只能使用FAT16格式 Verifying drive integrity, complete 正在校驗分區的完整性，完成 Your computer has NTFS partitions which may require large drive support. If you are using another operating system, such as Windows NT, which supports large drives you should enable treating these partitions as large 你的計算機有一個NTFS分區可能需要大分區支持，如果你正在使用其他操作系統，如Windows NT，你應該把這些分區分大一些 NOTE: If you answer Y and the partition display looks incorrect or a hang or crash occurs do nothing, run FDISK again, and answer N to this question 注意：如果你回答Y，可能顯示的分區信息看上去不正確或系統掛起或什么動作也沒有，這時你可再次運行FDISK，對這個問題用N回答 Should NTFS partitions on all drives be treated as large (Y/N)? 對所有的NTFS分區使用大分區模式 Drive deleted 驅動器被刪除 Partition made active 分區X被設置為活動 Primary DOS Partition created 主DOS分區被建立 Extended DOS Partition created 擴展DOS分區被建立 Logical DOS Drive created, drive letters changed or added 邏輯分區被建立，驅動器的盤符可能被改變或有新的增加 No partitions defined 沒有分區被定義 No logical drives defined 沒有邏輯驅動器被說明 Drive letters have been changed or deleted 驅動器盤符已經被改變或刪除 No active partitions 沒有設置活動分區，該硬盤不能被啟動 No fixed disks present 沒有硬盤 Error reading fixed disk 讀硬盤錯誤 Error writing fixed disk 寫硬盤錯誤 Write protect error writing fixed disk 寫硬盤寫保護錯誤 Incorrect DOS version 不正確的DOS版本 Cannot FDISK with network loaded 不能對網絡驅動器使用FDISK No space to create a DOS partition 沒有足夠的空間建立DOS分區 Requested logical drive size exceeds the maximum available space 輸入的邏輯驅動器的容量超過了最大可用的磁盤空間容量 Requested partition size exceeds the maximum available space 輸入的分區的容量超過了最大可用的磁盤空間容量 No partitions to delete 已經沒有分區可以被刪除 The only startable partition on Drive is already set active 硬盤X上的惟一的可啟動分區已經被標記為活動(擴展分區不能被設置為活動) No partitions to make active 沒有分區可以被標記為活動分區 Partition selected is not startable, active partition not changed 輸入的分區X不可啟動，當前的活動分區沒有被改變 Cannot create Extended DOS Partition without Primary DOS Partition on diskX 在硬盤X上沒有主DOS分區時不能建立擴展DOS 分區 All available space in the Extended DOS Partition is assigned to logical drives 擴展分區的全部有效空間都分配給邏輯驅動器嗎？還可以再分為主分區或其他分區 Cannot delete Extended DOS Partition while logical drives exist 因?yàn)閿U(kuò)展分區下有邏輯分區存在，所以擴展分區不能被刪除 All logical drives deleted in the Extended DOS Partition is not a choice. Please enter X 確定刪除哪一個邏輯分區，請輸入X WARNING! The partition set active is not startable 警告：被設置為活動的分區是不可啟動的 Only non-startable partitions exist 只有不可啟動的分區存在 Only partitions on Drive 1 can be made active 只有硬盤1上的分區可被設置為活動。當你掛接兩個以上硬盤時，使用FDISK命令時只能設置硬盤1中的某個主分區為活動，其他硬盤上的主分區都不能設置為活動 Maximum number of Logical DOS Drives installed 邏輯驅動器的所有盤符都使用，意思是你在分區時驅動器的盤符超過了Z Cannot create a zero size partition 不能建立大小空間為0的分區 Unable to access Drive X 不能訪問驅動器X Cannot delete Primary DOS Partition on drive 1 when an Extended DOS Partition exists 當擴展分區存在時不能刪除硬盤1上的主DOS分區 Invalid entry 無效的輸入 Volume label does not match 標不匹配，當你刪除分區時，系統會提示輸入該分區的卷標，如果輸入的巻標和你要?jiǎng)h除的分區的卷標不一致時，操作將不能進行 Cannot create Logical DOS Drive without an Extended DOS Partition on the current drive 沒有擴展分區時不能在當前硬盤上建立邏輯驅動器 Could not change partitions, because the disk could not be locked 不能改變分區，因?yàn)樵撚脖P不能被鎖定 Internal error 內部錯誤 Incorrect MS-DOS version 不正確的MS-DOS版本 Invalid parameter 無效的參數 Cannot FDISK with network loaded 不能對網絡驅動器進行FDISK The master boot code has NOT been updated/STATUS Displays partition information 主引導區代碼沒有被更新。顯示分區信息 /X Ignores extended disk-access support. Use this switch 不使用擴展磁盤訪問指令支持。當你使用 if you receive disk access or stack overflow messages 這個參數時你將看到堆棧溢出的信息 /MBR and /CMBR cannot both be specified /MBR和/CMBR這兩個參數不能同時使用 /MBR only operates on drive 1,use /CMBR for other drives 只能對硬盤1使用，/CMBR對其他硬盤使用/MBR You must specify a drive number with /CMBRInvalid partition table 在使用/C