真空吸塵器耐壓測試規范標準

1、 真空吸塵器耐壓測試修訂日期修訂單號修訂容摘要頁次版次修訂審核批準2011/03/30/系統文件新制定2A/0/真空吸塵器耐壓測試1.0 Purpose / 目的To evaluate the performance of dielectric voltage-withstand of the sample評估樣機絕緣材料的絕緣耐壓性能.2.0 Definition/概念:None無.3.0 Reference Documents/參考文獻:U.L.1017 CAN/CSA-C22.2 NO.243-01, dated 12-7-2001,CL 5.114.0 Equipment/設備:Wit

2、hstanding voltage tester(耐壓測試儀).5.0 General Instructions/說明:5.1 Tests may be conducted at any ambient temperature within a range of 10-40 (50-100).測試可在1040(50100)之的環境溫度下進行.5.2 Unless otherwise noted, all tests are to be conducted with appliance connected to a 120VAC, 60Hz power source. 除非另外標注, 否則所有樣

3、板都將連接在120V/60Hz電源下進行測試.5.3 All equipment used must be calibrated on an annual basis. Calibration stickers with last calibration and calibration due date must be affixed to each instrument.使用的所有設備都必須以一年為周期進行調校.載有最后調校日期和調校周期的調校粘紙必須粘固在每一個儀表上.5.4 Apply a 60-hertz essentially sinusoidal potential between

4、 current-carrying parts and dead metal parts.在帶電零部件和不帶電零部件之間施加60Hz測試電壓.5.5 Determine the test voltage(測試電壓的判定):a) One thousand volts for a sample employing a motor rated 1/2 horsepower (373 watts output) or less;馬達功率標稱小于373瓦的樣機, 測試電壓為1000V.b) One thousand volts plus twice the rated voltage for a sam

5、ple employing a motor rated more than 1/2 horsepower, or except as noted in (c) a sample applied directly to persons or supported by the body of a person.馬達功率標稱大于373瓦其直接與人體接觸或由人體支撐的樣機（此條排除以下c情況）, 測試電壓為1000V加上二倍的額定電壓240V, 即為1240Vc) Twenty-five hundred volts for a wet pick-up sample that is supported

6、by the body of a person but not solely hand held;對于人體支撐而不是只用手持的吸濕式樣機應為2500V. Test duration is 1 minute測試時間為一分鐘.6.0 Procedure/步驟:6.1 Obtain a representative sample of the appliance to be tested.準備一個有代表性的樣機用于測試.6.2 Obtain Test Results Form TTR1007 and completely fill in the information describing the

7、sample and the equipment used prior to running the test.用TTR1007測試結果的表格,在測試前完整地填入樣機和使用的設備的情況.6.3 Connect the tester to supply mains of 220V/60Hz, push down the power button, and set the test voltage range to 2.5 KV, trip current to 55MIU , time to 65s, then push down “START” button, turn the test vo

8、ltage knob to some extent clockwise and insert the probe connected to red lead into the socket connected to black lead, pressing the “STOP” button when hearing alarm which shows that the tester is ok in function. Turn off the tester, and turn the voltage knob counter-clockwise to its end.耐壓測試儀連接到220

9、V/60Hz電源, 開啟耐壓測試儀電源開關，設置電壓檔為2.5KV,跳脫電流為5MIU,定時65s. 按下“測試開始鍵”，順時針調節測試電壓旋鈕到顯示屏上顯示非零值,將其紅線相連的測試棒插入黑線輸出插座插孔，聽到報警聲時按下“測試停止鍵”，表示耐壓測試儀功能正常，關掉耐壓測試儀. 逆時針將測試電壓旋鈕旋到底.6.4 Operate the sample until thoroughly heated.按照TAREGP1001在開口空載狀況下運行樣機到熱穩定.6.5 Place the sample on the work bench and wrap the motor enclosure w

10、ith 10×20 cm metalfoil affecting the heat dissipations (if the enclosure area is less than 10×20 cm, wrap it with the same size metal foil).停止運行樣機, 將其置于絕緣工作臺上,用10×20cm錫箔紙蓋住離馬達最近的馬達殼但不要影響樣板散熱,如果馬達殼面積小于10×20cm就用其同樣大小錫薄紙將其全部包住.6.6 Plug the sample into the test socket and turn on tes

11、ter.將樣機電源線的插頭插入耐壓儀測試插座,樣機開關置于“ON”位.6.7 Make sure the control switch of the sample in “ON” position, touch the probe on the metal foil closely, then push down the “ START” button and turn the voltage knob letting the voltage from zero to the specified value gradually within 5 seconds. Turn off the te

12、ster when test is over and turn the voltage knob counter-clockwise to its end.開啟耐壓測試儀的電源開關,將測試棒緊觸在錫箔紙上，按下“測試開始鍵”，在5s調節電壓從0V起逐步到要求的測試電壓值，聽到耐壓測試儀結束提示音，關掉耐壓測試儀, 將測試電壓旋鈕按逆時針方向旋到底.7.0 Results/結果:7.1 Use the corresponding Test Results Form TTR1007 to report all numerical results as the information describ

13、ed below.使用TTR1007測試結果的表格, 除報告所有數字結果外, 還有下列描述的數據.7.2 Clearly and completely describe all parts that are part of this evaluation. Include all model numbers, manufacturing date codes, materials, plastic part revision letters, and modification status.清楚并完整地描述本評估的所有零件, 包括所有型號名稱, 材料和塑料零件改版符號.7.3Clearly and c