華為S9300核心交換機鏈路聚合配置實例

1、華為S9300核心交換機鏈路聚合配置實例配置靜態LACP模式鏈路聚合示例組網需求如圖1所示，在兩臺S9300設備上配置靜態LACP模式鏈路聚合組，提高兩設備之間的帶寬與可靠性，具體要求如下：· 2條活動鏈路具有負載分擔的能力。· 兩設備間的鏈路具有1條冗余備份鏈路，當活動鏈路出現故障鏈路時，備份鏈路替代故障鏈路，保持?jǐn)?shù)據傳輸?shù)目煽啃浴D1 配置靜態LACP模式鏈路聚合組網圖 配置思路采用如下的思路配置靜態LACP模式鏈路聚合：1. 在S9300設備上創建Eth-Trunk，配置Eth-Trunk為靜態LACP模式。2. 將成員接口加入Eth-Trunk。3. 配置系統優先級

2、確定主動端。4. 配置活動接口上限閾值。5. 配置接口優先級確定活動鏈路。數據準備為完成此配置例，需準備如下的數據：· 兩端S9300設備鏈路聚合組編號。· S9300-A系統優先級。· 活動接口上限閾值。· 活動接口LACP優先級。操作步驟1. 創建編號為1的Eth-Trunk，配置它的工作模式為靜態LACP模式 # 配置S9300-A。<Quidway> system-viewQuidway sysname S9300-AS9300-A interface eth-trunk 1S9300-A-Eth-Trunk1 mode lacp-s

3、taticS9300-A-Eth-Trunk1 quit# 配置S9300-B。<Quidway> system-viewQuidway sysname S9300-BS9300-B interface eth-trunk 1S9300-B-Eth-Trunk1 mode lacp-staticS9300-B-Eth-Trunk1 quit2. 將成員接口加入Eth-Trunk # 配置S9300-A。S9300-A interface gigabitethernet 1/0/1S9300-A-Gigabitethernet1/0/1 eth-trunk 1S9300-A-Giga

4、bitethernet1/0/1 quitS9300-A interface gigabitethernet 1/0/2S9300-A-Gigabitethernet1/0/2 eth-trunk 1S9300-A-Gigabitethernet1/0/2 quitS9300-A interface gigabitethernet 1/0/3S9300-A-Gigabitethernet1/0/3 eth-trunk 1S9300-A-Gigabitethernet1/0/3 quit# 配置S9300-B。S9300-B interface gigabitethernet 1/0/1S930

5、0-B-Gigabitethernet1/0/1 eth-trunk 1S9300-B-Gigabitethernet1/0/1 quitS9300-B interface gigabitethernet 1/0/2S9300-B-Gigabitethernet1/0/2 eth-trunk 1S9300-B-Gigabitethernet1/0/2 quitS9300-B interface gigabitethernet 1/0/3S9300-B-Gigabitethernet1/0/3 eth-trunk 1S9300-B-Gigabitethernet1/0/3 quit3. 在S93

6、00-A上配置系統優先級為100，使其成為LACP主動端 S9300-A lacp priority 1004. 在S9300-A上配置活動接口上限閾值為2 5. S9300-A interface eth-trunk 16. S9300-A-Eth-Trunk1 max bandwidth-affected-linknumber 2S9300-A-Eth-Trunk1 quit7. 在S9300-A上配置接口優先級確定活動鏈路 8. S9300-A interface gigabitethernet 1/0/19. S9300-A-Gigabitethernet1/0/1 lacp prio

7、rity 10010. S9300-A-Gigabitethernet1/0/1 quit11. S9300-A interface gigabitethernet 1/0/212. S9300-A-Gigabitethernet1/0/2 lacp priority 100S9300-A-Gigabitethernet1/0/2 quit13. 驗證配置結果 # 查看各S9300設備的Eth-Trunk信息，查看鏈路是否協商成功。S9300-A display eth-trunk 1 Eth-Trunk1's state information is: Local: LAG ID:

8、1 WorkingMode: STATIC Preempt Delay: Disabled Hash arithmetic: According to SA-XOR-DA System Priority: 100 System ID: 00e0-fca8-0417Least Active-linknumber: 1 Max Active-linknumber: 2Operate status: Up Number Of Up Port In Trunk: 2 - ActorPortName Status PortType PortPri PortNo PortKey PortState Wei

9、ght GigabitEthernet1/0/1 Selected 1GE 100 6145 2865 11111100 1 GigabitEthernet1/0/2 Selected 1GE 100 6146 2865 11111100 1 GigabitEthernet1/0/3 Unselect 1GE 32768 6147 2865 11100000 1 Partner: - PartnerPortName SysPri SystemID PortPri PortNo PortKey PortState GigabitEthernet1/0/1 32768 00e0-fca6-7f85

10、 32768 6145 2609 11111100 GigabitEthernet1/0/2 32768 00e0-fca6-7f85 32768 6146 2609 11111100 GigabitEthernet1/0/3 32768 00e0-fca6-7f85 32768 6147 2609 11110000S9300-B display eth-trunk 1 Eth-Trunk1's state information is: Local: LAG ID: 1 WorkingMode: STATIC Preempt Delay: Disabled Hash arithmet

11、ic: According to SA-XOR-DA System Priority: 32768 System ID: 00e0-fca6-7f85 Least Active-linknumber: 1 Max Active-linknumber: 8 Operate status: Up Number Of Up Port In Trunk: 2 - ActorPortName Status PortType PortPri PortNo PortKey PortState Weight GigabitEthernet1/0/1 Selected 1GE 32768 6145 2609 1

12、1111100 1 GigabitEthernet1/0/2 Selected 1GE 32768 6146 2609 11111100 1 GigabitEthernet1/0/3 Unselect 1GE 32768 6147 2609 11100000 1 Partner: - PartnerPortName SysPri SystemID PortPri PortNo PortKey PortState GigabitEthernet1/0/1 100 00e0-fca8-0417 100 6145 2865 11111100 GigabitEthernet1/0/2 100 00e0

13、-fca8-0417 100 6146 2865 11111100 GigabitEthernet1/0/3 100 00e0-fca8-0417 32768 6147 2865 11110000通過以上顯示信息可以看到，S9300-A的系統優先級為100，高于S9300-B的系統優先級。Eth-Trunk的成員接口中Gigabitethernet 1/0/1、Gigabitethernet 1/0/2成為活動接口，處于“Selected”狀態，接口Gigabitethernet 1/0/3處于“Unselect”狀態，同時實現M條鏈路的負載分擔和N條鏈路的冗余備份功能。配置文件·

14、S9300-A的配置文件# sysname S9300-A# lacp priority 100#interface Eth-Trunk1 mode lacp-static max active-linknumber 2#interface GigabitEthernet1/0/1 eth-trunk 1 lacp priority 100#interface GigabitEthernet1/0/2 eth-trunk 1 lacp priority 100#interface GigabitEthernet1/0/3 eth-trunk 1#return· S9300-B的配置文