規格書SPT204A2013VIP

1、· Beijing Singure Measurement & Control Tech. Co., LTD北京星格測控技術有限公司SPECIFICATION規格書Customer Name（客戶名稱）Description產品類型 Potential Transformer電壓互感器Customer Part No參數比2mA/2mAPart Nmber型號SPT204AElectrical Specifications電氣規范Mechanical Dimensions in mm同名端為對角Rated Primary Voltage Vi(V)原邊電壓（V）100,150

2、,220,300,380Primary Current(mA) 原邊電流（mA）2Secondary Current(mA)副邊電流（mA）2Dielectric withstanging Voltage(HI-pot)耐壓3000 VrmsAccuracy class精度等級0.1絕緣電阻（M）500MWinding tesistance副邊電阻（）110±10Mechanical Specifications機械規范CUPEncapsulant灌封EpooxyTerminals管腳4Pin*0.8Approx.Weight重量14g±2Tolerance公差（mm）&#

3、177;0.3Storage temp. -25<T<+80,Insulation resiatance Measured ResultSample No.6%10%20%100%120%1f (%)0.1280.1000.007-0.002-0.002()26.2624.5921.6012.0111.072f (%)0.1210.0800.077-0.037-0.037()33.0031.0127.7915.3014.003f (%)0.1080.0920.005-0.011-0.008()27.1225.6822.2211.1710.19推薦電路：使用方法簡介：SPT204實際

4、上是一款毫安級精密電流互感器，輸入額定電流為2mA，額定輸出電流為2mA。用戶使用時需要將電壓信號變換成電流信號，推薦使用電路如圖所示。圖中，R是限流電阻，不論額定輸入電壓多大，調整R的值，使額定輸入電流為2mA，就滿足使用條件。副邊電路是電流/電壓變換電路，當需要電壓輸出時采用。調整圖中反饋電阻R和r的值可得到所需要的電壓輸出。電容C1及可調電阻r是用來補償相移的。建議R取Vo/0.002,r取R/10，C1取值約為65/R（µF）, r '取200k 。電容C2和C3是400至1000pF的小電容，用來去耦和濾波。兩個反接的二極管是起保護運算放大器作用的。運算放大器視精度

5、要求使用，推薦使用OP07系列，使用性能較好的運算放大器較容易達到較高的精度和較好的穩定性。運算放大器電源電壓通常取+15V或+12V，也可根據具體情況自定。圖中電阻R和R要求精度優于1%, 溫度系數優于50PPM，R ' 的功率要求有2 倍的余量。用戶使用推薦電路稍加改動也可構成單電源供電模式，適用于單極性A/D轉換器的輸入。額定輸入電流也可以選為1mA以降低功耗或5mA以減小相移，線性度仍優于0.1%。SPT204次級如不加運算放大器而直接并聯一個電阻使輸出變換成電壓信號也是可以的。前提是電阻要小于400W，輸出電壓最大1伏，這時仍能得到線性度優于0.1%的輸出電壓信號。和推薦電路

6、比較，其影響如下：1.縮小了互感器的動態范圍。2.使相移增大。Usage Brief Introduction: SPT 204A is one of the milliampere class high accuracy current mini transformer, rated input 2 mA, rated output 2 mA, when using need transfer voltage signal into current signal, suggest use the electronic circle as below, as the picture showe

7、d, R is the current limiting resistor, no matter what is the rated input, adjust the R to the 2mA, can meet the usage. Sub-circuit is current/voltage transfer to circuit, use this when voltage output, adjust the reactive resistance showed in this picture R and r can get the rated output you need. Ca

8、pacitance CI and adjustable resistance are use to compensate phase shift. Suggest R use Vo/0.002, r use R/10, CI use approximate 65/R（F）， r use 200k. Capacitance C2 is 400-1000PF small capacitance, use to shake proof and filter. C3 can antijamming, the max number will be 400pf. The Diode is use to p

9、rotect the operational amplifier. Suggest use the OP07 series operational amplifier, use the better capability operational amplifier, can easy to reach a high accuracy and reliability. Operational amplifier power usually use +15V or +12V, can also set this according users need. Resistance R and Rs a

10、s showed in the picture require temperature priority 50 PPM, R power require have double residue. User use the recommended circle can also adjust it to form a single power model, apply to single A/D transformers input. Rated input can also choose 1mA to reduce consumption or 5 mA to cut down phase shift, nonlinearity is still precede 0.1. SPT 204 Sub if dont add an operational amplifier, but parallel connect a resistance directly let output transfer to voltage signal is also ok. But the precondition is resistance need smaller that 500R, rated output max 1V, and can sti