螺紋基本尺寸對照表.doc

1、螺紋根本尺寸對照表.doc英制管螺紋根本尺寸及公差牙形角 55ºBSPP P 螺紋代號 根本直徑 內螺紋 外螺紋 大徑 中徑 小徑 中徑公差 小徑公差 A 級 B 級 中徑公差 大徑公差 中徑公差 大徑公差 G1/8 ″ _ 28 9.728 9.147 8.566 +0.170+0.282 0 0 -0.107 0 -0.214 0 -0.214 0 -0.214 G1/4 ″ _ 19 13.157 12.301 11.445 +0.125 +0.445 -0.125 -0.250 -0.250 0-0.250 G3/8 &

2、Prime; _ 19 16.662 15.806 14.950 +0.125 0 +0.445 0 0 -0.125 0 -0.250 0 -0.250 0 -0.250 G1/2 ″ _ 14 20.955 19.793 18.631 +0.142 0 +0.541 0 0 -0.142 0 -0.284 0 -0.284 0 -0.284 G5/8 ″ _ 14 22.911 21.749 20.587 +0.142 0 +0.541 0 0 -0.142 0 -0.284 0 -0.284 0 -0.284 G3/4 ″ _

3、14 26.441 25.279 24.117 +0.142 0 +0.541 0 0 -0.142 0 -0.284 0 -0.284 0 -0.284 G1 ″ _ 11 33.249 31.770 30.291 +0.180 0 +0.640 0 0 -0.180 0 -0.360 0 -0.360 0 -0.360 G1.1/4 ″ _ 11 41.910 40.431 38.952 +0.180 0 +0.640 0 0 -0.180 0 -0.360 0 -0.360 0 -0.360 G1.1/2 ″ _ 11 47.8

4、03 46.324 44.854 +0.180 0 +0.640 0 0 -0.180 0 -0.360 0 -0.360 0 -0.360 G2 ″ _ 11 59.614 58.135 56.656 +0.180 0 +0.640 0 0 -0.180 0 -0.360 0 -0.360 0 -0.360 G2.1/2”_11 75.184 73.705 72.226 +0.217 0 +0.640 0 0 -0.217 0 -0.434 0 -0.434 0 -0.434 G3”_11 87.884 86.405 84.926 +0.217 0 +0.640 0 0

5、-0.217 0 -0.434 0 -0.434 0 -0.434 G3.1/2”_11 100.330 98.851 97.372 +0.217 0 +0.640 0 0 -0.217 0 -0.434 0 -0.434 0 -0.434 英制錐管螺紋根本尺寸及公差牙形角 55ºBSPT 螺紋代號 基面上的直徑 基準長度 有效螺紋長度 圓錐內螺紋基面軸向位移偏向 ±mm大徑 中徑 小徑 根本 最大 最小 根本 最大 最小 R1/8 ″ _ 28 9.728 9.147 8.566 4.0 4.9 3.1 6.5 7.4 5.6 1.

6、1 R1/4 ″ _ 19 13.157 12.301 11.445 6.0 7.3 4.7 9.7 11.0 8.4 1.7 R3/8 ″ _ 19 16.662 15.806 14.950 6.4 7.7 5.1 10.1 11.4 8.8 1.7 R1/2 ″ _ 14 20.955 19.793 18.631 8.2 10.0 6.4 13.2 15.0 11.4 2.3 R3/4 ″ _ 14 26.441 25.279 24.117 9.5 11.3 7.7 14.5 16.3 12.7 2.3 R1

7、″ _ 11 33.249 31.770 30.291 10.4 12.7 8.1 16.8 19.1 14.5 2.9 R1.1/4 ″ _ 11 41.910 40.431 38.952 12.7 15.0 10.4 19.1 21.4 16.8 2.9 R1.1/2 ″ _ 11 47.803 46.324 44.845 12.7 15.0 10.4 19.1 21.4 16.8 2.9 R2 ″ _ 11 59.614 58.135 56.656 15.9 18.2 13.6 23.4 25.7 21.1

8、2.9 R2.1/2”_11 75.184 73.705 72.226 17.5 21.0 14.0 26.7 30.2 23.2 3.5 R3”_11 87.884 86.405 84.926 20.6 24.1 17.1 29.8 33.3 26.3 3.5 R3.1/2”_11 100.330 98.851 97.372 22.2 25.7 18.7 31.4 34.9 27.9 3.5 美制管螺紋根本尺寸及公差牙形角 60ºUN(F) 螺紋代號 外螺紋 內螺紋 公差等級 公差等級 2A 2B 大徑 中徑 小徑 小徑 中徑 大徑 最大 最小 最大 最小最小 最大 最小

9、最大JIC 螺紋 7/16 ″ _ 20UNF 11.079 10.874 10.254 10.147 9.568 9.728 10.033 10.287 10.424 11.113 1/2 ″ _ 20UNF 12.667 12.461 11.841 11.732 11.156 11.328 11.608 11.875 12.017 12.7 9/16 ″ _ 18UNF 14.252 14.031 13.335 13.221 12.573 12.751 13.081 13.371 13.52 14.288 3/4 &Pri

10、me; _ 16UNF 19.012 18.773 17.981 17.854 17.12 17.323 17.678 18.019 18.184 19.05 7/8 ″ _ 14UNF 22.184 21.923 21.006 20.869 20.025 20.269 20.676 21.046 21.224 22.225 1-1/16 ″ _ 12UN 26.944 26.655 25.57 25.425 24.425 24.689 25.146 25.613 25.801 26.988 1-5/16 ″ _ 12UN 33.29

11、4 33.005 31.92 31.773 30.775 31.039 31.496 31.963 32.154 33.338 1-5/8 ″ _ 12UN 41.229 40.94 39.885 39.705 38.71 38.989 39.446 39.901 40.094 41.275 1-7/8 ″ _ 12UN 47.579 47.29 46.205 46.053 45.06 45.339 45.796 46.251 46.449 47.625 2-1/2 ″ _ 12UN 63.452 63.162 62.078 61.9

12、2 60.932 61.214 61.671 62.126 62.332 63.5 ORFS 螺紋 9/16 ″ _ 18UNF 14.252 14.031 13.335 13.221 12.573 12.751 13.081 13.371 13.52 14.288 11/16 ″ _ 16UN 17.427 17.188 16.396 16.274 15.535 15.748 16.104 16.431 16.589 17.463 13/16 ″ _ 16UN 20.599 20.361 19.568 19.444 18.707 1

13、8.923 19.279 19.606 19.766 20.638 1 ″ _ 14UNF 25.357 25.095 24.178 24.036 23.195 23.444 23.825 24.221 24.407 25.4 1-3/16 ″ _ 12UN 30.119 29.83 28.745 28.598 27.6 27.864 28.321 28.788 28.979 30.163 1-7/16 ″ _ 12UN 36.467 36.177 35.093 34.943 33.947 34.214 34.671 35.138 3

14、5.331 36.513 1-11/16 ″ _ 12UN 42.817 42.527 41.443 41.29 40.297 40.564 41.021 41.488 41.686 42.863 2 ″ _ 12UN 50.754 50.465 49.38 49.225 48.235 48.514 48.971 49.426 49.627 50.8 SAE 螺紋 5/8 ″ _ 18UNF 15.839 15.618 14.923 14.803 14.161 14.351 14.681 14.958 15.11 15.875 1-1

15、/16 ″ _ 14UN 26.947 26.683 25.743 25.608 24.74 24.968 25.375 25.783 25.961 26.987 其它美制螺紋 9/16 ″ _ 16UN 14.252 14.013 13.221 13. 12.36 12.573 12.929 13.256 13.411 14.288 7/8 ″ _ 12UN 22.182 21.892 20.808 20.668 19.662 19.939 20.396 20.851 21.034 22.225 2-1/4 ″

16、_ 12UN 57.104 56.815 55.73 55.575 54.585 54.864 55.321 55.776 55.976 57.15 注：UNC 粗牙螺紋系列，UNF 細牙螺紋系列， UNEF 超細牙螺紋系列， UN 不變螺距系列 布錐管螺紋根本尺寸及公差(牙形角 60º)NPT 螺紋代號 基面上的直徑 螺紋長度 大徑 中徑 小徑 有效長度 管端至基面長 Z1/8 ″ _ 27 10.272 9.519 8.766 7 4.572 Z1/4 ″ _ 18 13.572 12.443 11.314 9.5 5.080 Z3

17、/8 ″ _ 18 17.055 15.926 14.797 10.5 6.096 Z1/2 ″ _ 14 21.223 19.772 18.321 13.5 8.028 Z3/4 ″ _ 14 26.568 25.117 23.666 14 8.611 Z1 ″ _ 11.5 33.228 31.461 29.694 17.5 10.160 Z1.1/4 ″ _ 11.5 41.985 40.218 38.451 18 10.688 Z1.1/2 ″ _ 11.5 48.0

18、54 46.287 44.520 18.5 10.688 Z2 ″ _ 11.5 60.092 58.325 56.558 19 11.074 公制螺紋根本尺寸及公差(牙形角 60º)M M 螺紋代號 根本直徑 內 螺 紋 外螺紋 大 徑 中 徑 小 徑 公 差 等 級 公差等級 6H 7H 6g 中徑公差 小徑公差 中徑公差 小徑公差 中徑公差 大徑公差 M10_1 10 9.350 8.917 +0.150 0 +0.236 0 +0.190 0 +0.300 0 -0.026 -0.138 -0.026 -0.206 M12_1 12 11.350

19、10.917 +0.160 0 +0.236 0 +0.20_0 +0.300 0 -0.026 -0.144 -0.026 -0.206 M14_1 14 13.350 12.917 +0.160 0 +0.236 0 +0.20_0 +0.300 0 -0.026 -0.144 -0.026 -0.206 M12_1.25 12 11.188 10.647 +0.180 0 +0.265 0 +0.224 0 +0.335 0 -0.028 -0.160 -0.028 -0.240 M14_1.25 14 13.188 12.647 +0.180 0 +0.265 0 +0.224 0 +

20、0.335 0 -0.028 -0.160 -0.028 -0.240 M12_1.5 12 11.026 10.376 +0.190 0 +0.300 0 +0.236 0 +0.375 0 -0.032 -0.172 -0.032 -0.268 M14_1.5 14 13.026 12.376 +0.190 0 +0.300 0 +0.236 0 +0.375 0 -0.032 -0.172 -0.032 -0.268 M16_1.5 16 15.026 14.376 +0.190 0 +0.300 0 +0.236 0 +0.375 0 -0.032 -0.172 -0.032 -0.2

21、68 M18_1.5 18 17.026 16.373 +0.190 0 +0.300 0 +0.236 0 +0.375 0 -0.032 -0.172 -0.032 -0.268 M20_1.5 20 19.026 18.376 +0.190 0 +0.300 0 +0.236 0 +0.375 0 -0.032 -0.172 -0.032 -0.268 M22_1.5 22 21.026 20.376 +0.190 0 +0.300 0 +0.236 0 +0.375 0 -0.032 -0.172 -0.032 -0.268 M24_1.5 24 23.026 22.376 +0.20

22、_0 +0.300 0 +0.250 0 +0.375 0 -0.032 -0.182 -0.032 -0.268 M26_1.5 26 25.026 24.376 +0.20_0 +0.300 0 +0.250 0 +0.375 0 -0.032 -0.182 -0.032 -0.268 M27_1.5 27 26.026 25.376 +0.20_0 +0.300 0 +0.250 0 +0.375 0 -0.032 -0.182 -0.032 -0.268 M30_1.5 30 29.026 28.376 +0.20_0 +0.300 0 +0.250 0 +0.375 0 -0.032

23、 -0.182 -0.032 -0.268 M33_1.5 33 32.026 31.376 +0.20_0 +0.300 0 +0.250 0 +0.375 0 -0.032 -0.182 -0.032 -0.268 M36_1.5 36 35.026 34.376 +0.20_0 +0.300 0 +0.250 0 +0.375 0 -0.032 -0.182 -0.032 -0.268 M39_1.5 39 38.026 37.376 +0.20_0 +0.300 0 +0.250 0 +0.375 0 -0.032 -0.182 -0.032 -0.268 M42_1.5 42 41.026 40.376 +0.20_0 +0.300 0 +0.250 0 +0.375 0 -0.032 -0.182 -0.032 -0.268 M27_2 27 25.701 24.835 +0.224 0 +0.375 0 +0.280 0 +0.475 0 -0.038 -0.208 -0.038 -0.318 M30_2 30 28.701 27.835 +0.224 0 +0.375 0 +0.280 0 +0.475 0 -0.038 -0.208 -0.038 -0.318